Conductivity

- 1 side connected to solenoid valve connector without seal ("Plug and Play", as plug only has to be plugged onto measuring cell)- 1 side labelled cable with wire end ferruleswhite: PT100brown: PT100yellow: Measuring cell SL green: Measuring cellblue: shielding

- 1 side connected to solenoid valve connector without seal ("Plug and Play", as plug only has to be plugged onto measuring cell)- 1 side labelled cable with wire end ferruleswhite: PT100brown: PT100yellow: Measuring cell SL green: Measuring cellblue: shielding

2-electrode principleproven versions for industrial use measuring ranges 0 ... 1 mS/cm (K = 0.1) or 0.01 ... 15 mS/cm (K = 1.0) temperature range up to 55 °C, maximum pressure up to 6 bar at 25 °C JUMO ecoLine CR-PVC conductive 2-electrode conductivity sensorBrief description: Conductivity sensors of the 202923 series are used, for example, in general water technology, cooling and air-conditioning systems, drinking and bathing water, or in industrial rinsing and process water circuits. The body material PVC limits the application to medium temperatures up to 55 °C. Two versions with cell constants K = 0.1 or 1.0 are available. Versions with the common thread sizes G 3/4" or G 1" or a plug-in version are available for installation. The plug-in version is used, for example, with the matching PVC tees in nominal sizes DN 25, 32 and 40 and allows the sensor to be quickly dismantled for cleaning or maintenance. The electrical connection is made either via a detachable device plug or via a fixed cable connection. The overall construction and the parts in contact with the medium are physiologically harmless. The electrode material is stainless steel (K = 0.1) or special graphite (K = 1.0). The optionally integrable temperature sensor allows simultaneous recording of the medium temperature for temperature compensation in downstream measuring amplifiers.Stainless steel variant K = 0.1 The sensor has 3 metallic pin electrodes. The two outer pins are electrically connected and form one pole of the 2-electrode conductivity sensor. The counter electrode is the middle stainless steel pin. This design achieves very high measurement precision with low stray fields. A temperature sensor can be integrated in the middle pin. Graphite variant K = 1.0 For physical reasons, special graphite is used as the electrode material for higher conductance values. The two graphite electrodes are completely integrated in the electrode shaft. The optional temperature sensor is located in a stainless steel sleeve that is immersed in the measured medium. Operating principleThe sensors of the 202923 series are 2-electrode conductivity sensors. An AC voltage is applied to them by the transmitter. The current flowing across the liquid and the electrodes is determined by the conductivity of the liquid

2-electrode principleproven versions for industrial use measuring ranges 0 ... 1 mS/cm (K = 0.1) or 0.01 ... 15 mS/cm (K = 1.0) temperature range up to 55 °C, maximum pressure up to 6 bar at 25 °C JUMO ecoLine CR-PVC conductive 2-electrode conductivity sensorBrief description: Conductivity sensors of the 202923 series are used, for example, in general water technology, cooling and air-conditioning systems, drinking and bathing water, or in industrial rinsing and process water circuits. The body material PVC limits the application to medium temperatures up to 55 °C. Two versions with cell constants K = 0.1 or 1.0 are available. Versions with the common thread sizes G 3/4" or G 1" or a plug-in version are available for installation. The plug-in version is used, for example, with the matching PVC tees in nominal sizes DN 25, 32 and 40 and allows the sensor to be quickly dismantled for cleaning or maintenance. The electrical connection is made either via a detachable device plug or via a fixed cable connection. The overall construction and the parts in contact with the medium are physiologically harmless. The electrode material is stainless steel (K = 0.1) or special graphite (K = 1.0). The optionally integrable temperature sensor allows simultaneous recording of the medium temperature for temperature compensation in downstream measuring amplifiers.Stainless steel variant K = 0.1 The sensor has 3 metallic pin electrodes. The two outer pins are electrically connected and form one pole of the 2-electrode conductivity sensor. The counter electrode is the middle stainless steel pin. This design achieves very high measurement precision with low stray fields. A temperature sensor can be integrated in the middle pin. Graphite variant K = 1.0 For physical reasons, special graphite is used as the electrode material for higher conductance values. The two graphite electrodes are completely integrated in the electrode shaft. The optional temperature sensor is located in a stainless steel sleeve that is immersed in the measured medium. Operating principleThe sensors of the 202923 series are 2-electrode conductivity sensors. An AC voltage is applied to them by the transmitter. The current flowing across the liquid and the electrodes is determined by the conductivity of the liquid

2-electrode principleproven versions for industrial use measuring ranges 0 ... 1 mS/cm (K = 0.1) or 0.01 ... 15 mS/cm (K = 1.0) temperature range up to 55 °C, maximum pressure up to 6 bar at 25 °C JUMO ecoLine CR-PVC conductive 2-electrode conductivity sensorBrief description: Conductivity sensors of the 202923 series are used, for example, in general water technology, cooling and air-conditioning systems, drinking and bathing water, or in industrial rinsing and process water circuits. The body material PVC limits the application to medium temperatures up to 55 °C. Two versions with cell constants K = 0.1 or 1.0 are available. Versions with the common thread sizes G 3/4" or G 1" or a plug-in version are available for installation. The plug-in version is used, for example, with the matching PVC tees in nominal sizes DN 25, 32 and 40 and allows the sensor to be quickly dismantled for cleaning or maintenance. The electrical connection is made either via a detachable device plug or via a fixed cable connection. The overall construction and the parts in contact with the medium are physiologically harmless. The electrode material is stainless steel (K = 0.1) or special graphite (K = 1.0). The optionally integrable temperature sensor allows simultaneous recording of the medium temperature for temperature compensation in downstream measuring amplifiers.Stainless steel variant K = 0.1 The sensor has 3 metallic pin electrodes. The two outer pins are electrically connected and form one pole of the 2-electrode conductivity sensor. The counter electrode is the middle stainless steel pin. This design achieves very high measurement precision with low stray fields. A temperature sensor can be integrated in the middle pin. Graphite variant K = 1.0 For physical reasons, special graphite is used as the electrode material for higher conductance values. The two graphite electrodes are completely integrated in the electrode shaft. The optional temperature sensor is located in a stainless steel sleeve that is immersed in the measured medium. Operating principleThe sensors of the 202923 series are 2-electrode conductivity sensors. An AC voltage is applied to them by the transmitter. The current flowing across the liquid and the electrodes is determined by the conductivity of the liquid

Technical data: Screw-in thread: 1/2 "Material housing: POM black Material electrodes: V4A 4571 Material O-ring: EPDM Cell constant: C=0.1 +/- 10%. Max. Operating pressure: 6 bar Max. Operating temperature: 60°C Temperature sensor: PT100 Solenoid valve connector: ST2+SL electrodes Colour cable green/yellow St1+St2 PT 100 Colour cable brown/white

Technical data: Screw-in thread: 1/2 "Material housing: POM black Material electrodes: V4A 4571 Material O-ring: EPDM Cell constant: C=1.0 +/- 10%. Max. Operating pressure: 6 bar Max. Operating temperature: 60°C Temperature sensor: PT100 Solenoid valve connector: ST2+SL electrodes Colour cable green/yellow St1+St2 PT 100 Colour cable brown/white

Technical data: Screw-in thread: 3/4"Material housing: POM black Material electrodes: V4A 4571 Material O-ring: EPDM Cell constant: C=0.1 +/- 10%. Max. Operating pressure: 6 bar Max. Operating temperature: 60°C Temperature sensor: PT100 Solenoid valve connector: ST2+SL electrodes Colour cable green/yellow St1+St2 PT 100 Colour cable brown/white

Technical data: Screw-in thread: 3/4"Material housing: POM black Material electrodes: V4A 4571 Material O-ring: EPDM Cell constant: C=1.0 +/- 10%. Max. Operating pressure: 6 bar Max. Operating temperature: 60°C Temperature sensor: PT100 Solenoid valve connector: ST2+SL electrodes Colour cable green/yellow St1+St2 PT 100 Colour cable brown/white

High-quality conductivity meter with a 4-20mA signal output for forwarding the measured value to a higher-level control system, for example. The measurement is temperature compensated and therefore offers you an accurate measurement result. Also here we have the possibility to offer you an individual design regarding the connection, the LEDs including the measuring range up to a private label.  Due to the acrylic glass cover used, the light of the LEDs is widely scattered and the current LED status can be seen from a distance in darker rooms.  Quality Made in Germany. LED configuration according your requirements (1 green LED, 1 red LED): <.... µS/cm = green >.... µS/cm to <....µS/cm = green/red flashing >.... µS/cm = red Technical data: Measuring range: 0 - 2000 μS/cm Temperature compensation: Linear 2.2 % / K, reference temperature 25°C Accuracy conductivity: +/-10% of the maximum full scale value Accuracy temperature: +-1.0 °C Limit value display: Optical via LED Analog output: 4-20 mA = 0-2000 μS/cm Power supply: 24 VDC +-10% Power consumption: < 2.5W Screw-in thread: according yor requirements Housing: POM (polyoxymethylene) Vision panel: PMMA (acrylic glass) Electrodes: stainless steel 1.457 Dimensions: Diameter 60 mm x 60 mm (top) / 100 mm (total) Gaskets electrodes: EPDM, 28 x 3 mm Gasket housing: EPDM, 50 x 2 mm Application limits: P max: 6 bar; T max: 50 °C Protection class: IP 65*

High-quality conductivity meter with a 4-20mA signal output for forwarding the measured value to a higher-level control system, for example. The measurement is temperature compensated and therefore offers you an accurate measurement result. Also here we have the possibility to offer you an individual design regarding the connection, the LEDs including the measuring range up to a private label.  Due to the acrylic glass cover used, the light of the LEDs is widely scattered and the current LED status can be seen from a distance in darker rooms.  Quality Made in Germany. Standard LED configuration (1 green LED, 1 red LED): <1500 µS/cm = green >1500 µS/cm to <1900µS/cm = green/red flashing >1900 µS/cm = red Technical data: Measuring range: 0 - 2000 μS/cm Temperature compensation: Linear 2.2 % / K, reference temperature 25°C Accuracy conductivity: +/-10% of the maximum full scale value Accuracy temperature: +-1.0 °C Limit value display: Optical via LED Analog output: 4-20 mA = 0-2000 μS/cm Power supply: 24 VDC +-10% Power consumption: < 2.5W Screw-in thread: 3/4" Housing: POM (polyoxymethylene) Vision panel: PMMA (acrylic glass) Electrodes: stainless steel 1.457 Dimensions: Diameter 60 mm x 60 mm (top) / 100 mm (total) Gaskets electrodes: EPDM, 28 x 3 mm Gasket housing: EPDM, 50 x 2 mm Application limits: P max: 6 bar; T max: 50 °C Protection class: IP 65*

High-quality conductivity meter with a 4-20mA signal output for forwarding the measured value to a higher-level control system, for example. The measurement is temperature compensated and therefore offers you an accurate measurement result. Also here we have the possibility to offer you an individual design regarding the connection, the LEDs including the measuring range up to a private label.  Due to the acrylic glass cover used, the light of the LEDs is widely scattered and the current LED status can be seen from a distance in darker rooms.  Quality Made in Germany. Standard LED configuration (1 green LED, 1 red LED): <1500 µS/cm = green >1500 µS/cm to <1900µS/cm = green/red flashing >1900 µS/cm = red Technical data: Measuring range: 0 - 2000 μS/cm Temperature compensation: Linear 2.2 % / K, reference temperature 25°C Accuracy conductivity: +/-10% of the maximum full scale value Accuracy temperature: +-1.0 °C Limit value display: Optical via LED Analog output: 4-20 mA = 0-2000 μS/cm Power supply: 24 VDC +-10% Power consumption: < 2.5W Screw-in thread: according to your requirements Housing: POM (polyoxymethylene) Vision panel: PMMA (acrylic glass) Electrodes: stainless steel 1.457 Dimensions: Diameter 60 mm x 60 mm (top) / 100 mm (total) Gaskets electrodes: EPDM, 28 x 3 mm Gasket housing: EPDM, 50 x 2 mm Application limits: P max: 6 bar; T max: 50 °C Protection class: IP 65*

High-quality conductivity meter with a 4-20mA signal output for forwarding the measured value to a higher-level control system, for example. The measurement is temperature compensated and therefore offers you an accurate measurement result. Also here we have the possibility to offer you an individual design regarding the connection, the LEDs including the measuring range up to a private label.  Due to the acrylic glass cover used, the light of the LEDs is widely scattered and the current LED status can be seen from a distance in darker rooms.  Quality Made in Germany. LED configuration like requested (1 green LED, 1 red LED): <... µS/cm = green >... µS/cm to <...µS/cm = green/red flashing >... µS/cm = red Technical data: Measuring range: 0 - 2000 μS/cm Temperature compensation: Linear 2.2 % / K, reference temperature 25°C Accuracy conductivity: +/-10% of the maximum full scale value Accuracy temperature: +-1.0 °C Limit value display: Optical via LED Analog output: 4-20 mA = 0-2000 μS/cm Power supply: 24 VDC +-10% Power consumption: < 2.5W Screw-in thread: 3/4"  Housing: POM (polyoxymethylene) Vision panel: PMMA (acrylic glass) Electrodes: stainless steel 1.457 Dimensions: Diameter 60 mm x 60 mm (top) / 100 mm (total) Gaskets electrodes: EPDM, 28 x 3 mm Gasket housing: EPDM, 50 x 2 mm Application limits: P max: 6 bar; T max: 50 °C Protection class: IP 65*

High-quality conductivity meter with a 4-20mA signal output for forwarding the measured value to a higher-level control system, for example. The measurement is temperature compensated and therefore offers you an accurate measurement result. Also here we have the possibility to offer you an individual design regarding the connection, the LEDs including the measuring range up to a private label.  Due to the acrylic glass cover used, the light of the LEDs is widely scattered and the current LED status can be seen from a distance in darker rooms.  Quality Made in Germany. LED configuration according your requirements (1 green LED, 1 red LED): <.. µS/cm = green >..µS/cm to <...µS/cm = green/red flashing >.. µS/cm = red Technical data: Measuring range: 0 - 50 μS/cm  Temperature compensation: Linear 2.2 % / K, reference temperature 25°C Accuracy conductivity: +/-10% of the maximum full scale value Accuracy temperature: +-1.0 °C Limit value display: Optical via LED Analog output: 4-20 mA = 0-50 μS/cm Power supply: 24 VDC +-10% Power consumption: < 2.5W Screw-in thread: according your requirements Housing: POM (polyoxymethylene) Vision panel: PMMA (acrylic glass) Electrodes: stainless steel 1.457 Dimensions: Diameter 60 mm x 60 mm (top) / 100 mm (total) Gaskets electrodes: EPDM, 28 x 3 mm Gasket housing: EPDM, 50 x 2 mm Application limits: P max: 6 bar; T max: 50 °C Protection class: IP 65*

High-quality conductivity meter with a 4-20mA signal output for forwarding the measured value to a higher-level control system, for example. The measurement is temperature compensated and therefore offers you an accurate measurement result. Also here we have the possibility to offer you an individual design regarding the connection, the LEDs including the measuring range up to a private label.  Due to the acrylic glass cover used, the light of the LEDs is widely scattered and the current LED status can be seen from a distance in darker rooms.  Quality Made in Germany. Standard LED configuration (1 green LED, 1 red LED): <20 µS/cm = green >20 µS/cm to <40µS/cm = green/red flashing >40 µS/cm = red Technical data: Measuring range: 0 - 50 μS/cm Temperature compensation: Linear 2.2 % / K, reference temperature 25°C Accuracy conductivity: +/-10% of the maximum full scale value Accuracy temperature: +-1.0 °C Limit value display: Optical via LED Analog output: 4-20 mA = 0-50 μS/cm Power supply: 24 VDC +-10% Power consumption: < 2.5W Screw-in thread: 3/4"  Housing: POM (polyoxymethylene) Vision panel: PMMA (acrylic glass) Electrodes: stainless steel 1.457 Dimensions: Diameter 60 mm x 60 mm (top) / 100 mm (total) Gaskets electrodes: EPDM, 28 x 3 mm Gasket housing: EPDM, 50 x 2 mm Application limits: P max: 6 bar; T max: 50 °C Protection class: IP 65*

High-quality conductivity meter with a 4-20mA signal output for forwarding the measured value to a higher-level control system, for example. The measurement is temperature compensated and therefore offers you an accurate measurement result. Also here we have the possibility to offer you an individual design regarding the connection, the LEDs including the measuring range up to a private label.  Due to the acrylic glass cover used, the light of the LEDs is widely scattered and the current LED status can be seen from a distance in darker rooms.  Quality Made in Germany. Standard LED configuration (1 green LED, 1 red LED): <20 µS/cm = green >20 µS/cm to <40µS/cm = green/red flashing >40 µS/cm = red Technical data: Measuring range: 0 - 50 μS/cm Temperature compensation: Linear 2.2 % / K, reference temperature 25°C Accuracy conductivity: +/-10% of the maximum full scale value Accuracy temperature: +-1.0 °C Limit value display: Optical via LED Analog output: 4-20 mA = 0-50 μS/cm Power supply: 24 VDC +-10% Power consumption: < 2.5W Screw-in thread: according to your requirements Housing: POM (polyoxymethylene) Vision panel: PMMA (acrylic glass) Electrodes: stainless steel 1.457 Dimensions: Diameter 60 mm x 60 mm (top) / 100 mm (total) Gaskets electrodes: EPDM, 28 x 3 mm Gasket housing: EPDM, 50 x 2 mm Application limits: P max: 6 bar; T max: 50 °C Protection class: IP 65*

High-quality conductivity meter with a 4-20mA signal output for forwarding the measured value to a higher-level control system, for example. The measurement is temperature compensated and therefore offers you an accurate measurement result. Also here we have the possibility to offer you an individual design regarding the connection, the LEDs including the measuring range up to a private label.  Due to the acrylic glass cover used, the light of the LEDs is widely scattered and the current LED status can be seen from a distance in darker rooms.  Quality Made in Germany. LED configuration according your requirement (1 green LED, 1 red LED): <... µS/cm = green >... µS/cm to <...µS/cm = green/red flashing >... µS/cm = red Technical data: Measuring range: 0 - 50 μS/cm  Temperature compensation: Linear 2.2 % / K, reference temperature 25°C Accuracy conductivity: +/-10% of the maximum full scale value Accuracy temperature: +-1.0 °C Limit value display: Optical via LED Analog output: 4-20 mA = 0-50 μS/cm Power supply: 24 VDC +-10% Power consumption: < 2.5W Screw-in thread: 3/4"  Housing: POM (polyoxymethylene) Vision panel: PMMA (acrylic glass) Electrodes: stainless steel 1.457 Dimensions: Diameter 60 mm x 60 mm (top) / 100 mm (total) Gaskets electrodes: EPDM, 28 x 3 mm Gasket housing: EPDM, 50 x 2 mm Application limits: P max: 6 bar; T max: 50 °C Protection class: IP 65*

High-quality conductivity meter with a 4-20mA signal output for forwarding the measured value to a higher-level control system, for example. The measurement is temperature compensated and therefore offers you an accurate measurement result. Also here we have the possibility to offer you an individual design regarding the connection, the LEDs including the measuring range up to a private label.  Due to the acrylic glass cover used, the light of the LEDs is widely scattered and the current LED status can be seen from a distance in darker rooms.  Quality Made in Germany. Standard LED configuration (1 green LED, 1 red LED): <20 µS/cm = green >20 µS/cm to <40µS/cm = green/red flashing >40 µS/cm = red Technical data: Measuring range: according to your requirements Temperature compensation: Linear 2.2 % / K, reference temperature 25°C Accuracy conductivity: +/-10% of the maximum full scale value Accuracy temperature: +-1.0 °C Limit value display: Optical via LED Analog output: 4-20 mA = 0-50 μS/cm Power supply: 24 VDC +-10% Power consumption: < 2.5W Screw-in thread: according to your requirements Housing: POM (polyoxymethylene) Vision panel: PMMA (acrylic glass) Electrodes: stainless steel 1.457 Dimensions: Diameter 60 mm x 60 mm (top) / 100 mm (total) Gaskets electrodes: EPDM, 28 x 3 mm Gasket housing: EPDM, 50 x 2 mm Application limits: P max: 6 bar; T max: 50 °C Protection class: IP 65*

High-quality conductivity meter with a 4-20mA signal output for forwarding the measured value to a higher-level control system, for example. The measurement is temperature compensated and therefore offers you an accurate measurement result. Also here we have the possibility to offer you an individual design regarding the connection, the LEDs including the measuring range up to a private label.  Due to the acrylic glass cover used, the light of the LEDs is widely scattered and the current LED status can be seen from a distance in darker rooms.  Quality Made in Germany. LED configuration like requested (1 green LED, 1 red LED): <... µS/cm = green >... µS/cm to <...µS/cm = green/red flashing >... µS/cm = red Technical data: Measuring range: according to your requirements Temperature compensation: Linear 2.2 % / K, reference temperature 25°C Accuracy conductivity: +/-10% of the maximum full scale value Accuracy temperature: +-1.0 °C Limit value display: Optical via LED Analog output: 4-20 mA = 0-... μS/cm (according your measuring range) Power supply: 24 VDC +-10% Power consumption: < 2.5W Screw-in thread: 3/4" Housing: POM (polyoxymethylene) Vision panel: PMMA (acrylic glass) Electrodes: stainless steel 1.457 Dimensions: Diameter 60 mm x 60 mm (top) / 100 mm (total) Gaskets electrodes: EPDM, 28 x 3 mm Gasket housing: EPDM, 50 x 2 mm Application limits: P max: 6 bar; T max: 50 °C Protection class: IP 65*

High-quality conductivity meter with a 4-20mA signal output for forwarding the measured value to a higher-level control system, for example. The measurement is temperature compensated and therefore offers you an accurate measurement result. Also here we have the possibility to offer you an individual design regarding the connection, the LEDs including the measuring range up to a private label.  Due to the acrylic glass cover used, the light of the LEDs is widely scattered and the current LED status can be seen from a distance in darker rooms.  Quality Made in Germany. LED configuration according your needs (1 green LED, 1 red LED): <... µS/cm = green >... µS/cm to <...µS/cm = green/red flashing >... µS/cm = red Technical data: Measuring range: according your requirements Temperature compensation: Linear 2.2 % / K, reference temperature 25°C Accuracy conductivity: +/-10% of the maximum full scale value Accuracy temperature: +-1.0 °C Limit value display: Optical via LED Analog output: 4-20 mA = 0-... μS/cm (according your measuring range) Power supply: 24 VDC +-10% Power consumption: < 2.5W Screw-in thread: according your requirements Housing: POM (polyoxymethylene) Vision panel: PMMA (acrylic glass) Electrodes: stainless steel 1.457 Dimensions: Diameter 60 mm x 60 mm (top) / 100 mm (total) Gaskets electrodes: EPDM, 28 x 3 mm Gasket housing: EPDM, 50 x 2 mm Application limits: P max: 6 bar; T max: 50 °C Protection class: IP 65*

High-quality conductivity meter with a 4-20mA signal output for forwarding the measured value to a higher-level control system, for example. The measurement is temperature compensated and therefore offers you an accurate measurement result. Also here we have the possibility to offer you an individual design regarding the connection, the LEDs including the measuring range up to a private label.  Due to the acrylic glass cover used, the light of the LEDs is widely scattered and the current LED status can be seen from a distance in darker rooms.  Quality Made in Germany. Standard LED configuration (1 green LED, 1 red LED): <20 µS/cm = green >20 µS/cm to <40µS/cm = green/red flashing >40 µS/cm = red Technical data: Measuring range: according your requirements Temperature compensation: Linear 2.2 % / K, reference temperature 25°C Accuracy conductivity: +/-10% of the maximum full scale value Accuracy temperature: +-1.0 °C Limit value display: Optical via LED Analog output: 4-20 mA = 0-... μS/cm (according your needed measuring range) Power supply: 24 VDC +-10% Power consumption: < 2.5W Screw-in thread: 3/4" Housing: POM (polyoxymethylene) Vision panel: PMMA (acrylic glass) Electrodes: stainless steel 1.457 Dimensions: Diameter 60 mm x 60 mm (top) / 100 mm (total) Gaskets electrodes: EPDM, 28 x 3 mm Gasket housing: EPDM, 50 x 2 mm Application limits: P max: 6 bar; T max: 50 °C Protection class: IP 65*