Conductivity is an ability of a substance (liquids, solids, gas), to conduct electricity and heat. The conductivity can only show the amount that are dissolved in water in total. The unit is expressed in Siemens per meter [S/m] in SI units or usually by microsiemens per centimeter [µS/cm]. TDS stands for "Total Dissolved Solids" and is approximated by conductivity using a multiplication factor and expressed in parts per million (ppm). The following conversion key applies: 1.2 µS/cm = 1 ppm = 1 mg/l.
Our conductivity
sensor is a cost-effective solution for continuous online monitoring of
conductivity/TDS of your process water. With 4-20mA or MODBUS/RS485 output, it
can be easily connected to our multiparameter system NTM and read sensor
signal.
Our Neomeris Select high temperature conductivity cells are suitable in a wide range of high performance applications with high temperatures and pressures.To meet these demanding technical requirements, our sensors are manufactured from 316 stainless steel with PEEK elements and feature a one-piece cell design suitable for high pressure conditions. The conductivity cells are available with different cell constants (0.1/cm and 1.0/cm) and temperature sensors (PT100 and PT1000) and are designed for a specific pressure-temperature range. Certain model types also allow you to choose between a short and long thread, depending on the installation situation.Our 1/2" inch Select LF stainless steel conductivity cell is a general purpose sensor that can be used in a variety of standard applications such as in cooling towers or water treatment plants, etc. and is easy to install. In contrast, our Select HTLF Ultra high performance conductivity cell is the top of the range model. This conductivity sensor is specially designed for boiler applications where it is permanently integrated in the boiler. Via our selection menu you can easily choose the right conductivity sensor for your application. Please contact us if you have any questions.
Our Neomeris Select high temperature conductivity cells are suitable in a wide range of high performance applications with high temperatures and pressures.To meet these demanding technical requirements, our sensors are manufactured from 316 stainless steel with PEEK elements and feature a one-piece cell design suitable for high pressure conditions. The conductivity cells are available with different cell constants (0.1/cm and 1.0/cm) and temperature sensors (PT100 and PT1000) and are designed for a specific pressure-temperature range. Certain model types also allow you to choose between a short and long thread, depending on the installation situation.Our 1/2" inch Select LF stainless steel conductivity cell is a general purpose sensor that can be used in a variety of standard applications such as in cooling towers or water treatment plants, etc. and is easy to install. In contrast, our Select HTLF Ultra high performance conductivity cell is the top of the range model. This conductivity sensor is specially designed for boiler applications where it is permanently integrated in the boiler. Via our selection menu you can easily choose the right conductivity sensor for your application. Please contact us if you have any questions.
Our Neomeris Select high temperature conductivity cells are suitable in a wide range of high performance applications with high temperatures and pressures.To meet these demanding technical requirements, our sensors are manufactured from 316 stainless steel with PEEK elements and feature a one-piece cell design suitable for high pressure conditions. The conductivity cells are available with different cell constants (0.1/cm and 1.0/cm) and temperature sensors (PT100 and PT1000) and are designed for a specific pressure-temperature range. Certain model types also allow you to choose between a short and long thread, depending on the installation situation.Our 1/2" inch Select LF stainless steel conductivity cell is a general purpose sensor that can be used in a variety of standard applications such as in cooling towers or water treatment plants, etc. and is easy to install. In contrast, our Select HTLF Ultra high performance conductivity cell is the top of the range model. This conductivity sensor is specially designed for boiler applications where it is permanently integrated in the boiler. Via our selection menu you can easily choose the right conductivity sensor for your application. Please contact us if you have any questions.
Analog and digital communication interface for process visualization• Modbus or 4-20 mA sensor output available• Configuration and calibration can be performed using the web-based software Corrosion-, coating- and fouling-resistant • The sensor is made of Noryl material and therefore offers a wide range of applications. It is also temperature-resistant up to 105°C (up to 80°C when installed in a T-piece, up to 70°C for the Modbus and 4-20 mA versions) Mounting and installation• The sensor can be installed in a T-piece specially designed for this sensor or, for example, attached to a pipe for immersion mounting using the 3/4" MNPT thread Wide measuring range• Measures conductivity in the range of 0 – 2,000,000 μS (2 S)
Analogue and digital communication for more process visibility• Modbus or 4-20 mA sensor output available• Configuration and calibration can be done using web based software Corrosion, Coating and Fouling Resistant• Noryl body has a wide solvent tolerance and temperature stability to 105°C (used with flow cell 80°C, with integrated 4-20mA output or Modbus 70°C) Mounting• Can be installed in line using the specific flow cell or submersed via the 3/4" MNPT thread Wide Measurement Range• Can measure conductivity from 0 – 500.000 μS (0 - 500 mS)
Analog and digital communication interface for process visualization• Modbus or 4-20 mA sensor output available• Configuration and calibration can be performed using the web-based software Corrosion-, coating- and fouling-resistant • The sensor is made of Noryl material and therefore offers a wide range of applications. It is also temperature-resistant up to 105°C (up to 80°C when installed in a T-piece, up to 70°C for the Modbus and 4-20 mA versions) Mounting and installation• The sensor can be installed in a T-piece specially designed for this sensor or, for example, attached to a pipe for immersion mounting using the 3/4" MNPT thread Wide measuring range• Measures conductivity in the range of 0 – 2,000,000 μS (2 S)
Analog and digital communication interface for process visualization• Modbus or 4-20 mA sensor output available• Configuration and calibration can be performed using the web-based software Corrosion-, coating- and fouling-resistant • The sensor is made of Noryl material and therefore offers a wide range of applications. It is also temperature-resistant up to 105°C (up to 80°C when installed in a T-piece, up to 70°C for the Modbus and 4-20 mA versions) Mounting and installation• The sensor can be installed in a T-piece specially designed for this sensor or, for example, attached to a pipe for immersion mounting using the 3/4" MNPT thread Wide measuring range• Measures conductivity in the range of 0 – 2,000,000 μS (2 S)